メソポーラス機能性酸化膜を機能膜とする電気化学デバイスに関する研究
堀内保 · Institutional Repositories DataBase (IRDB)
This article reports electrochromic device, dye-sensitized solar cells and perovskite solar cells with nano-porous electrode. 1. Electrochromic device/ Electrochromic devices have attracted considerable attention as energy conservation devices, in that they can induce reversible changes in the physical properties of light by imparting electric charge to chemicals. The problem with the TiO2 device is that although both the color and bleached states of an electrochromic device fabricated by a high temperature annealing process show high levels of response, the color and bleached states of a device fabricated by a low temperature process show very low response levels. We found that a SnO2 nanocrystalline film is effective for use in electrochromic devices. The impedance of SnO2 was two orders of magnitude lower than that of TiO2 annealed at 450 °C. The electrochromic device with SnO2 has a high ∆OD compared with TiO2, and a bleached state response time similar to that of TiO2 annealed at 450 °C. 2. Dye-sensitized solar cells/ 2-1. Solid-state dye-sensitized solar cells/ General solid-state dye-sensitized solar cells have been used in the spin-coating process for filling hole-transport materials in porous TiO2 electrodes. We found that the hole-transport materials were filled in the porous TiO2 electrode by the spray method of liquid crystal hole-transport materials with a heating substrate or the supercritical CO2 fluid method. Then, appearance of the porous TiO2 was observed from a section SEM image. The energy conversion efficiency of solid-state dye-sensitized solar cells using the supercritical CO2 fluid was compared with that of Gratzel’s laboratory using the same materials, and 4.2% energy conversion efficiency was observed under AM1.5 irradiation. This energy conversion efficiency was slightly higher than that for Gratzel’s laboratory. We found that solid-state dye-sensitized solar cell has good performance for indoor light. It was found that the ionic potential of the hole-transport layer was shifted by the basicity of pyridine compounds; especially large shift of the ionic potential was obtained by strongly basic pyridine compounds. Thus, the energy level matching between the highest occupied molecular orbital of the sensitizing dye and the ionic potential of the hole-transporting layer improved. In addition, the shunt resistances of the solar cell were improved using strongly basic pyridine compounds. We have demonstrated series–connected solid-state dye-sensitized solar cell module with non-divided active layer, such as nano-porous TiO2 layer and hole-transporting layer. This module come into existence only divided the transparent conductive electrode and counter electrode. This behavior is ascribed to hole-transporting layer has 6 digit higher impedance compared to iodine electrolyte. The photovoltaic performance of this non-divided module is almost same compared to divided module. Moreover, this non-divided module has good light shielding performance compared to amorphous-silicon solar cell. 2-2. Development of Sensitizing dye/ We found that the benzothiazole sensitized dye with a double-rhodanine ring has higher IPCE spectra than thiophene sensitized dye. The Segawa Laboratory of The University of Tokyo reported that the hybrid material formed from TiO2 and TCNQ shows strong interfacial charge transfer absorption in the visible region. We synthesized TCNQ derivatives and examined conditions of the adsorbent. The hybrid material performed well when supercritical fluid CO2 was used. 3. Development of Perovskite solar cells/ We examined the pre-treatment of the alanine that was similar compound for CH3NH3I and pre-treatment of PbI2. The Perovskite solar cells with pre-treatment performed well. In the sequential deposition method for the formation of the Perovskite, the CH3NH3I solution was coated on the PbI2 coating porous TiO2 electrode by the spin-coating method, which showed good photovoltaic performance. We found that different metal halide compounds added to the PbI2 largely suppressed crystallization. Moreover, the addition of SbI3 to PbI2 obtained IPCE values higher than PbI2 only.
Cited by 0 works. doi:10.18997/00007364